Vita Mix DRINK MACHINE MP User Manual

F O O D S E R V I C E  
Owner’s Manual  
Read And Save These Instructions  
®
BarBoss MP  
Drink Machine MP  
Maximum Performance Commercial Blender  
All Models  
Important Safeguards  
Enjoy the safety of this grounded appliance. The Vita-Mix blender’s U.S. power cord  
comes equipped with a three-prong (grounding) plug which mates with a standard three-  
prong wall outlet (Figure A). This cord will vary for countries outside the United States.  
Adapters (Figure B) are available for two-prong outlets. Do not cut or remove the  
third (ground) prong from the plug or power cord.  
Consult your electrician if you are not sure if the wall outlet is grounded through the  
building wiring. With a properly grounded two prong wall outlet, ground the machine by  
attaching the tab on the adapter to the wall outlet cover by means of the screw in the  
center of the cover (Figure B).  
THREE PRONG  
ADAPTERS  
ARE NOT TO  
BE USED IN  
Figure A  
Figure B  
CANADA.  
Save These Safety Instructions  
3
®
BarBoss MP &  
Drink Machine MP Model  
OFF  
ON  
ON/OFF switch. Located on the front of the  
machine below the switch panel, controls the  
power to the machine. With the machine plugged  
in, switch the machine to ON to ready the  
machine for blending. Shut OFF power switch  
at night or whenever the machine will be left  
unattended.  
Note on Timers: Stop mid cycle with  
START/STOP switch, not the  
ON/OFF switch. If the ON/OFF  
switch was used, wait 30 seconds for  
power to recycle and the timer to  
reset before resuming operation.  
START TIMER switch. This is a lighted switch.  
When light is lit power is ON. Depress START  
TIMER switch to activate timer setting and again  
to stop midcycle.  
During operation, you may interrupt timer by  
pressing START/STOP switch.  
#5  
#4  
ax  
M
#3  
#2  
TIMER DIAL. Allows user to select a number  
of timed settings. Increments on timer are  
approximate seconds. Timer is activated only  
when the power switch is ON. Blender will shut  
off automatically at the end of the pre-set time.  
1
#
E
LS  
PU  
P
TO  
R
S
E
T/  
M
R
TI  
TA  
S
PULSE switch. Pulse button can only be used  
when the power switch is ON. The PULSE  
switch can be used to quickly refresh product  
in the container by depressing the switch and  
holding down as long as needed.  
NOTE: Switches will become sticky from use. Use a wet cloth or sponge to flush and  
clean in the groove around the water-shielded switches. You may also lightly spray  
the surface around the switches with an all purpose cleaner (such as Cinch® or 409®)  
and work the switches back and forth a few times to loosen any dried residue under  
switch. Leaving switches sticky will damage or burn out the switches.  
4
NOTE: Outside the United States and Canada, your machine may come with a different  
container configuration.  
To secure lid plug, rotate it so one  
tab locks between the stops on top  
of rubber lid  
Two-Part Lid  
32 oz. (900 ml) Xtreme Performance Container  
The two part lid is easy to clean and easy to put  
Lift lid tabs  
on, take off and seal.  
to remove lid  
To remove a fully latched lid, lift the two  
tabs and pull upward and off.  
• Twist the center lid plug to fasten or  
remove.  
NOTE: Older 48 oz. (1.4 L) and 64 oz. (2.0 L)  
Vita-Mix container will work on the BarBoss or  
Drink Machine MP. The Xtreme Performance  
Containers will not work on older Vita-Mix  
Machines. Call Vita-Mix or your distributor for  
more information.  
Figure A  
One Piece Lid (optional)  
32 oz. (900 ml) Xtreme Performance Container  
The one piece lid is easy to clean and easy to put  
on, and take off and seal.  
Figure B  
• There is no lid plug for this lid.  
• Add ingredients through port on top.  
NOTE: To make new lids easier to insert and remove, rub a light coating of cooking oil  
around bottom where it seals. Place it in container for several minutes, remove and  
lightly wipe oil off lid.  
5
®
BarBoss MP & Drink Machine MP Instructions  
1. Set the container on the motor base by aligning it over the centering pad anchored to  
the base. (Motor must be completely stopped before positioning container). Containers  
are not to be used for hard, dry materials. Avoid running your machine with the container  
empty.  
2. Place liquids and soft foods in the container first, solid items and ice last. Prepare  
food by cutting or breaking into 1-3 inch (3-8 cm) pieces. Frozen fruit should be as small  
as practical.  
3. Always use lid when blending. If blending hot ingredients, the lid must be securely in  
place. When processing hot liquids, DO NOT use a non-latching lid.  
4. Press ON/OFF switch to ON. Activate the timer by selecting the desired setting  
on the dial and then depressing the START/STOP TIMER switch on the left.  
NOTE: Each setting on the dial (#1 - #5 and MAX Blend) is an increase in time and  
speed. Your own testing will determine what setting will work best for your drinks.  
4a. If mixture stops circulating, you have likely trapped an air bubble. Either insert the  
tamper through the lid while blending, or stop the motor remove the container from  
the base and stir or scrape the mixture from the sides of container into the center  
using a rubber spatula to press any air bubbles away from the blades. Replace the  
lid and continue blending.  
Note: START/STOP TIMER switch on your machine is lit when power is ON. Avoid  
moveable parts. The timer stops working if machine is overloaded on low speed.  
Reset the machine by turning power OFF for 15 seconds.  
Warning: If you detect a change in the sound of the machine or if a hard or  
foreign object comes into contact with the blades, do not serve the drink.  
Inspect your blade assembly for loose, nicked or missing parts. If parts are  
loose, missing, or nicked replace with new blade assembly. (See page 8.)  
4b. To prevent possible splashing, lightly rest your hand on the lid while turning the  
machine on (except when processing hot liquids).  
4c. Due to the blending speed of the machine, processing times are greatly reduced  
over standard machines. Until you become accustomed to the speed, watch your  
mixture carefully to avoid over-blending.  
4d. If stopping the machine mid-cycle, use the START/STOP switch, not the POWER  
switch. If the POWER switch was used, wait 30 seconds for power to recycle and  
the timer to reset before resuming operation.  
5. After blender has been turned off, wait until blade comes to a complete stop before  
removing the lid or container from the motor base.  
6
Note: The thermal protector shuts the motor off to protect it from overheating. To restart,  
wait for motor to cool down with the power OFF (up to 30 minutes). When this happens,  
review your processing techniques and your instructions. Your recipes may be too thick  
or have too much material in them.  
Cooling may be quickened by placing the motor base in a refrigerator or a cool spot.  
Unplug first. To speed up the process try circulating the air with a vacuum or fan aimed  
at the bottom of the base. If the motor seems to be over heating (and the thermal  
overload protector has not turned the machine OFF), remove the container from the  
base. Set the timer for 20 seconds. Turn the machine ON and let the machine run for  
20 seconds. Repeat this step 3 times for a total of 1 minute.  
6. To use the PULSE switch: Press ON/OFF switch to ON. With the container on the  
motor base depress the PULSE switch. Release the switch to turn off the motor.  
7
Blade Agitator Assembly. Blades are sharp; use  
caution when handling the blade. When inserting the  
blade assembly through the container bottom, align the  
flat sides. Gravity holds it in place while the retainer nut  
is tightened. Do not attempt to disassemble this part.  
Drive Spline. Mates with drive socket on the motor  
base to turn the blade. Note: Removing and replacing  
your container while the coupling is still rotating will  
strip the drive spline “teeth”. (This part is NOT  
removable.)  
32  
Retainer Nut. Must be snug. Order the available  
retainer nut wrench for best results. (Refer to the  
diagram below to remove or replace.)  
Never use a blade assembly with loose, damaged or nicked components.  
Blade Assembly Removal  
CAUTION: Do not remove blades unless absolutely necessary!  
At times, it may be necessary to give your blades additional  
cleaning. An easy-to-use blade assembly removal wrench  
(Item #15596) may be purchased through your Vita-Mix  
distributor. Never attempt to take the blade assembly itself  
apart. This will void the warranty.  
Retainer Nut Wrench  
Turn the container upside down and grip firmly. Insert retainer  
nut wrench in groove of retainer nut and rotate counterclock-  
wise to loosen. Then grip blades with a cloth and remove  
retainer nut by hand.  
Replacing Blade Assembly  
With the container upside down, grip blades with cloth, insert  
into the container bottom and align with flat sides of container  
Retainer Nut Wrench  
in use.  
opening. Place retainer nut on and hand tighten. Last, carefully  
turn clockwise until secure, using wrench. Do not force. If it is  
not tight enough, you will notice increased container noise.  
8
The Accelerator Tool prevents an air bubble  
from forming while blending. It is used when  
making frozen ice creams, pureeing fruits  
and vegetables, (or whenever your mixture  
requires it). It also permits you to push  
ingredients down around the blades while  
the Vita-Mix blender is running.  
Accelerator Tool use:  
• Use only with the lid in place and the  
center lid plug removed.  
• The splash disc prevents the Accelerator  
Tool from hitting the blades when insert-  
ed through the lid.  
• Container should not be more than  
2/3 full (just below the indicated  
maximum capacity for XP containers)  
when the Accelerator Tool is left in place  
while blending.  
To avoid overheating, do not exceed  
30 seconds of continuous blending  
with Accelerator Tool in place.  
8
4
• If thick mixtures stop circulating, you  
have likely trapped an air bubble.  
Insert Accelerator Tool through the lid  
and stir to release it.  
• Holding the Accelerator Tool at an angle  
near the side and pushing towards the  
center will be more effective when  
creating a thicker, smoother drink.  
*NOTE: Accelerator Tools have a small step  
on them. The step prevents the Accelerator  
Tool from coming into contact with the blades  
in Vita-Mix polycarbonate containers.  
Accelerator Tool cannot be used with a one  
piece non-latching lid.  
9
Care Note  
To ensure that you get the longest possible life from your Vita-Mix product, we recom-  
mend the following products, when used as directed by the supplier:  
Cleaning Product. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supplier  
Solid Supra, Solid Power,.. . . . . . . . . . . . . . . . . . . . . . . . Ecolab, Inc., St. Paul, MN  
Guardian Acclaim, Solid Guardian Plus, . . . . . . . . . . . . . (800) 352-5326  
Solid Super Impact, Solid Insure. . . . . . . . . . . . . . . . . . . www.ecolab.com  
Diverpak. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diversey, Livonia, MI  
Eclipse H2, Liqui-Safe L7 . . . . . . . . . . . . . . . . . . . . . . . . (800) 521-8140  
Acclean . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Klenzade Products  
Poly-Brite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Division of Ecolab  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . St. Paul, MN  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (612) 293-2165  
Glow MB-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wesmar Company, Inc.  
Lustre NC-25 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Seattle, WA  
Lustre Plus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (206)783-5344  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . www.wesmar.com  
PSRA 41-D, PSRA 41-E . . . . . . . . . . . . . . . . . . . . . . . . . Anderson Chemical Co.  
Liqui-Ware 1, Liqui-Ware MC . . . . . . . . . . . . . . . . . . . . . Litchfield, MN  
D-Flex, Sur-Met . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (800) 366-2477  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . www.andersonchemical.com  
Rinse Aids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supplier  
Solid Rinse Dry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ecolab, Inc., St. Paul, MN  
Solid Brilliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (800) 352-5326  
Jet Dry, Rinse Dry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . www.ecolab.com  
Destainer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supplier  
NuWare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diversey, Livonia, MI  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (800) 521-8140  
Do not use abrasive cleaning agents or concentrated bleach  
when cleaning. Do not use any cleaners containing Quatinary Sanitizers  
on polycarbonate components (i.e., containers).  
NOTE: Switches will become sticky from use. Use a wet cloth or sponge to flush and  
clean in the groove around the water-shielded switches. You may also lightly spray the  
surface around the switches with an all-purpose cleaner (such as Cinch® or 409®) and  
work the switches back and forth a few times to loosen any dried residue under switch.  
Dirty switches may burn out.  
ADDITIONAL NOTE: Do not let mixtures, liquids and food products dry within the  
container. Rinse throughout use. Drying may lock around the blade and weaken/tear  
the bearings seal when restarted. Do not place containers in the freezer. Extremely  
low temperature combined with hot ingredients and/or the immediate rapid action of the  
blade may crack the container. Due to the nature of polycarbonates, microwaving and  
automatic dishwashing are not recommended. Follow the cleaning instructions on page 11.  
10  
Motor Base  
1. Unplug the power cord.  
2. Wash outside surface with a damp, soft cloth or sponge, which has been rinsed in a  
mild solution of liquid dish soap (Ivory Liquid® or equivalent) in warm water. NEVER  
IMMERSE MOTOR BASE IN WATER OR OTHER LIQUID.  
3. Thoroughly clean switches so that they work freely. They will become sticky from  
use. Use a wet cloth or sponge* to flush and clean in the groove around the water  
shielded switches. You may also lightly spray the surface around the switches with  
an all-purpose cleaner such as Cinch® or 409® and work the switches back and forth  
a few times to loosen any dried residue under switch.  
4. Polish with a soft cloth.  
*Note: Be sure to wring excess water out of cloth or sponge when cleaning around the  
controls or any electrical part.  
Lid  
Separate the lid and plug, then wash in warm soapy water. Rinse clean under running  
water and dry. Reassemble before use. (See page 5).  
Container  
1. To clean: Fill pitcher 1/4 full with warm (110˚F/43˚C) water and add a couple drops  
of dish soap.** Return container to motor base and firmly position the two part lid.  
Run machine for 30 seconds. Empty container. Repeat this step.  
** Note: To prolong polycarbonate container life, Vita-Mix recommends using soaps  
with a low Ph balance, such as a manual pot and pan detergent. Due to the nature  
of polycarbonates, automatic dishwashing is not recommended.  
2. Fill pitcher 3/4 full with warm (110˚F/43˚C) water (do not add soap). Return container  
to motor base and firmly position the two part lid. Run machine for 30 seconds.  
Empty container.  
3. If any solid residue remains, remove the blade agitator assembly (see page 8) and  
wash all container parts in warm soapy water. Rinse and drain. Reassemble before  
next step.  
4. To sanitize: If all solid residue is gone after step 2 or after completion of step 3,  
fill container 3/4 full with a sanitizing solution mix.*** Return container to motor base  
and firmly position the two part lid. Run machine on HIGH for 30 seconds. Empty  
container.  
5. Return container to motor base and run machine empty for an additional 5 seconds.  
Do not rinse after sanitizing.  
*** Recommended sanitizing solution: 1-1/2 teaspoons institutional or household  
bleach in 2 quarts (2 liters) water.  
11  
®
BarBoss MP & Drink Machine MP  
NOTE: Outside the United States and Canada, your machine may come with a different  
container configuration. Contact your local Vita-Mix distributor for part numbers.  
Item # Part  
#760  
#15578  
PLS209  
#891  
Accelerator tool  
Sound-reducing XP centering pad  
Variable speed control knob / timer control knob  
Drive socket  
XDM039  
#15585  
#15598  
#15571  
Owner’s Manual  
XP retainer nut  
XP blade agitator assembly  
32 oz. (900 ml) polycarbonate Xtreme Performance container with lid  
and lid plug  
#15574  
#15570  
#15573  
2-piece thermoplastic rubber lid for 32 oz. (900 ml) Xtreme  
Performance container  
32 oz. (900 ml) polycarbonate stackable Xtreme Performance  
container, ice blade & lid assembly  
32 oz. (900 ml) polycarbonate stackable Xtreme Performance  
container only  
*Notice: Other than the drive socket, blade assembly and retainer nut, this unit  
is not user serviceable.  
#755  
#15574  
#15575  
#15596  
#15573  
Retainer Nut Wrench  
(sold separately)  
OUNCES  
48  
40  
32  
#15571  
#15598  
#15585  
#891  
#PLS145  
One-Piece Lid  
(sold separately)  
#15578  
PLS209  
#760  
12  
Top four problems you can fix on your own  
1. Problem:  
Solution #1:  
• increased vibration  
• leaking from bottom of container  
• increased container noise  
Check blade assembly for loose, damaged  
or nicked components and replace.  
Solution #2:  
Tighten retainer nut with screwdriver  
moving clockwise until it is snug. See p. 8.  
2. Problem:  
• Machine will not run.  
Solution #1:  
Double-check to make sure power cord is  
firmly in power outlet.  
Solution #2:  
Check to make sure switches are clean  
and moving freely.  
Solution #3:  
The thermal protector may have turned  
the machine OFF. Turn power OFF for up  
to 30 minutes to reset. Note: Cooling may  
be quickened by placing the motor base in  
a refrigerator or cool spot. (Unplug first).  
To speed up the cooling process, try circu-  
lating the air with a fan or vacuum at the  
bottom of the motor base.  
3. Problem:  
Solution:  
• loud noise from blade area  
• blades don’t spin  
Drive socket may be broken. Check for a  
fine crack down the center or worn teeth-  
replace with a new drive socket. (Item #891).  
Instructions are included with part.  
4. Problem:  
Solution:  
• Machine will not run when START  
TIMER switch is activated.  
Check ON/OFF switch to make sure the  
switch is in the ON position. Note: START  
TIMER switch is lit when power is on.  
Timer stops working if machine is overloaded on low speed. Reset by turning power  
OFF for 15 seconds. Do not turn power OFF midway through a blending cycle.  
To interrupt cycle, press START/STOP TIMER switch one time. See page 4.  
If you cannot fix your machine with these suggestions, technical help is available by  
calling 800-4DRINK4 (800-437-4654). If outside the United States and Canada,  
contact your local Vita-Mix distributor or phone the Vita-Mix International Division at  
+1(440) 782-2450 or email [email protected] for a distributor in your country.  
13  
Vita-Mix Corporation warrants your Commercial Vita-Mix appliance to be free from  
defects in materials and workmanship for a period of three years from the date of  
purchase when used in accordance with the accompanying instruction booklet.  
Provisions of this limited warranty are void if your Vita-Mix appliance has been  
subjected to obvious abuse, negligence, accident, alteration, or failure to follow  
operating instructions, or product exposure to abnormal or extreme conditions.  
Cosmetic changes such as discoloration of parts of the product in the hands of the  
user or the effects of the use of abrasive cleaners will not be warranted or considered  
defects. The cleaning or removal of food products along with any damage caused by  
allowing them to build up is not covered by this limited warranty. Warranty is void if  
the Vita-Mix blender is put into a sound reduction chamber that does not allow  
proper cooling.  
In the event your Vita-Mix appliance needs service or repair covered by the terms of  
this warranty, please call the Vita-Mix Corporation for shipping instructions. The Vita-Mix  
blender must be sent in original or sufficient packaging.  
This limited warranty is in lieu of any other warranty expressed or implied. No  
representative or any other person is authorized to make any other warranty or to  
assume any liability not strictly in accordance with the foregoing. This limited warranty  
gives you specific legal rights which may vary from state to state. Proof of purchase  
may be required to prove date of purchase.  
Outside the Continental United States and Canada other warranties may apply.  
(Call or check with your local Vita-Mix distributor for details). In case of shipping damage,  
notify the shipper or carrier immediately. Outside the United States and Canada, contact  
your local Vita-Mix Distributor.  
14  
PLEASE NOTE: The Service Contract outlined in the following paragraphs applies  
only to customers in the United States and Canada. Customers in all other countries  
should contact their local Vita-Mix® distributor for service details.  
This Vita-Mix blender includes a 1-Year Service Contract effective from date of  
purchase. In the event your machine should need parts or repairs, covered under this  
Service Contract, call Vita-Mix customer service immediately for instructions. Proof of  
date of purchase may be required. This does not cover abuse, misuse, tampering,  
improper installation or extreme conditions.  
The Vita-Mix Service Contract includes the following:  
1. Only one extra drive socket - to facilitate simple repairs and prevent down time is  
included and packaged with each machine.  
2. Additional drivers and accelerator tool, unless defective, are not covered. NOTE: to  
determine if you have a defective part, please order a replacement part through  
Vita-Mix Customer Service and, when the new part arrives, return the old part in the  
same packaging. Vita-Mix will inspect the returned part and, if defective, issue a  
refund for the price of the new part. A part will be considered defective if no abuse or  
neglect was involved with its break. Non defective parts sent to Vita-Mix for inspection  
will not be returned if deemed unusable. Service Contract covers functionality of the  
machine but not abuse or lack of recommended maintenance.  
3. In the continental United States, sender pays freight one way to Vita-Mix  
Corporation. The Vita-Mix Corporation will pay UPS ground freight charges to return  
the machine to the sender. Sender pays costs for special shipping requests. Outside  
Continental United States, other service contracts may apply.  
Before returning this product for any reason, including repair, please, first contact our  
CUSTOMER SERVICE DEPARTMENT: (800) 4DRINK4, (800) 437-4654 or (440) 235-0214  
to receive a “RETURN AUTHORIZATION NUMBER”.  
Note: Within the United States, Limited Warranty and Service Contract are honored  
directly through the Vita-Mix Corporation, Cleveland, Ohio USA. Non-warranty repairs  
can be performed by any CFESA service center. For machines sold in the USA, call  
Vita-Mix (800) 4DRINK4 (800-437-4654) or (440) 235-0214.  
15  
Dimensions:  
Height of Motor Base: 8-1/2” (21.25 cm)  
• with 32 oz. (900 ml) polycarbonate Xtreme Performance container  
and lid: 18” (45.72 cm)  
• with 32 oz. (900 ml) polycarbonate Xtreme Performance container  
without lid: 16” (40.64 cm)  
32 oz. (900 ml) polycarbonate Xtreme Performance container with lid,  
no base: 10-3/4” (27.31 cm)  
Dimensions: 8” W x 9” D x 18” H (20.3 cm x 22.9 cm x 45.72 cm)  
Ship weight of machine: 13 lbs. (6 kg)  
Power Requirements:  
Volts: 120 VAC  
Amps: 11.5  
Hz: 50/60  
Volts: 220/240 VAC  
Watts: 750-850  
Hz: 50/60  
Volts: 100 VAC (Japan)  
Watts: 900  
Hz: 50/60  
NSF  
®
N
When applicable:  
The instructions appearing in this Owner’s Manual cannot cover every possible  
condition and situation that may occur. Common sense and caution must be  
practiced when operating and maintaining any appliance.  
VITA-MIX® CORPORATION  
Foodservice Division  
8615 Usher Road, Cleveland, Ohio 44138-2103 USA  
©2005 Vita-Mix Corporation. No part of this publication may be reproduced or transmitted in any form or  
by any means, electronic or mechanical, including photocopy, recording or any information storage and retrieval system  
without the written permission of the Vita-Mix Corporation.  
Printed in U.S.A.  
XDM039 11/05  

Westcott 1095 User Manual
Tektronix Camcorder 1780 R User Manual
Sony Handycam DCR TRV50 User Manual
Sony DVD653 User Manual
Sony Cyber Shot DSC TX200 User Manual
Sony Camcorder HXR MC2000U User Manual
Sony Camcorder EVI H100V User Manual
Sanyo Xacti VPC CG6 User Manual
Rosen Entertainment Systems 10.2 User Manual
Roland DS 8 DS 7 DS 5 User Manual