Zanussi Washer 192994960 00 202009 User Manual

EN  
User manual  
2
Washing Machine  
ZWF 14069W  
 
• Always be sure, that there is no water leakage from  
hoses and their connections after the installation.  
• If the applianceis installed in a location subject tofrost,  
please read the “dangers of freezing” chapter.  
• Any plumbing work required to install this appliance  
should be carried out by a qualified plumber or com-  
petent person.  
Child safety  
• This appliance is not intended for use by person (in-  
cluding children) with reduced physical sensory or  
mental capabilities or lack of experience and knowl-  
edge unless they have been given supervision or in-  
struction concerning use of the appliance by a person  
responsible for their safety.  
• The packaging components (e.g. plastic film, poly-  
styrene) can be dangerous to children - danger of suf-  
focation! Keep them out of children’s reach  
• Any electrical work required to install this appliance  
should be carried out by a qualified electrician or com-  
petent person.  
• Keep all detergents in a safe place out of children’s  
reach.  
• Make sure that children or pets do not climb into the  
drum. To prevent children and pets becoming trapped  
inside the drum this machine incorporates a special  
feature.  
Use  
• This appliance is designed for domestic use. It must  
not be used for purposes other than those for which it  
was designed.  
• Only wash fabrics which are designed to be machine  
washed. Follow the instructionsoneachgarmentlabel.  
• Do not overload the appliance. See the Washing Pro-  
gramme Table.  
• Before washing, ensure that all pockets are empty and  
buttons and zips are fastened. Avoid washing frayed or  
torn articles and treat stains such as paint, ink, rust,  
and grass before washing. Underwired bras must NOT  
be machine washed.  
• Garments which have been in contact with volatile pe-  
troleum products should not be machine washed. If  
volatile cleaning fluids are used, care should be taken  
to ensure that the fluid is removed from the garment  
before placing in the machine.  
• Never pull the power supply cable to remove the plug  
from the socket; always take hold of the plug itself.  
To activate this device, ro- To disable this device and  
tate the button (without  
pressing it) inside the  
restore the possibility of  
closing thedoor, rotatethe  
door clockwise until the button anti-clockwise un-  
groove is horizontal. If  
necessary use a coin.  
til the groove is vertical.  
• Never use the appliance if the power supply cable, the  
control panel, the working surface or the base are  
damaged so that the inside of the washing machine is  
accessible.  
3
 
Product description  
1
2
3
4
5
6
Detergent dispenser drawer  
Control panel  
Door opening handle  
Rating plate  
Drain pump  
Adjustable feet  
1
2
3
4
5
6
Detergent dispenser drawer  
Compartment for detergent used for prewash and  
soak phase or for stain remover used during the stain  
action phase (if available). The prewash and soak deter-  
gent is added at the beginning of the wash programme.  
The stain remover is added during the stain action phase.  
Compartment for powder or liquid detergent used for  
main wash. If using liquid detergent pour it just before  
starting the programme.  
Compartment for liquid additives (fabric softener,  
starch).  
Follow the product manufacturer’s recommendations on  
quantities to use and do not exceed the «MAX» mark in  
the detergent dispenser drawer. Any fabric softener or  
starching additives must be poured into the compartment  
before starting the wash programme.  
Control panel  
Below is a picture of the control panel. It shows the programme selector dial as well as the buttons and pilot  
lights. These are presented by relevant numbers on the following pages.  
4
 
1
2
3
4
5
7
6
1
2
3
4
Programme selector dial  
SPIN reduction button  
OPTIONS button  
5
6
7
START/PAUSE button  
DELAY START button  
Indicator pilot lights  
EXTRA RINSE button  
Table of symbols  
Night Cycle  
Rinse Hold  
Programme selector dial, spin speed button and available options  
in times with a more economical power rate. On some  
programmestherinseswill beperformedwithmorewater.  
Before opening the door it will be necessary to empty out  
the water. To empty out the water, please read the para-  
graph «At the end of the programme».  
Programme Selector Dial  
Itallowsyoutoswitchtheapplianceon/offand/ortoselect  
a programme.  
Available options:  
Spin  
By pressing this button you can change the spin speed of  
the selected programme or to select the Rinse Hold or the  
Night Cycle option.  
Prewash  
By selecting this option the machine performs a prewash  
cycle before the main wash phase. The washing time will  
be prolonged. This option is recommended for heavily  
soiled laundry.  
Rinse hold  
By selecting this function the water of the last rinse is not  
emptied out to prevent the fabrics from creasing. Before  
opening the door it will be necessary to empty out the  
water. To empty out the water, please read the paragraph  
«At the end of the programme».  
Economy  
Only for cottons and synthetic items lightly or normally  
soiled at a temperature of 40°C or higher. The washing  
time will be prolonged and the washing temperature will  
be reduced. You can use this option if you want to wash  
normally soiled laundry and at the same time save energy.  
Night Cycle  
By selecting this function the machine will not drain the  
water of the last rinse and all spinning phases will be  
suppressed, so as not to wrinkle the laundry. This wash-  
ing cycle is very quiet and it can be selected at night or  
5
 
Super Quick  
Indicator pilot light (7)  
Short cycle for lightly soiled items or for laundry which  
needs only freshening up. We recommend you to reduce  
the fabrics loading.  
After having pressed the  
button 5 the light 7.1  
(Wash) and 7.2 (Door) il-  
luminate to indicate that  
appliance is working and  
the door is locked.  
Extra Rinse  
This appliance is designed for saving energy. If it neces-  
sary to rinse the laundry using an extra quantity of water  
(extra rinse), select this option. Some additional rinses  
will be performed. This option isrecommended for people  
who are allergic to detergents, and in areas where the  
water is very soft.  
The light 7.2 (Door) indicates if the door can be opened:  
• The light is on: the door cannot be opened.  
• The light is off: the door can be opened.  
Start Pause  
This button allows you to start or to interrupt the selected  
programme.  
• The light is flashing: the door is unlocking and soon  
can be opened.  
The light 7.3 (End) illuminates at the end of the washing  
cycle.  
Delay Start  
The start of the programme can be delayed by 2, 4 or 8  
hours by means of this button.  
First use  
• Ensure that the electrical and water connections  
comply with the installation instructions.  
• Remove the polystyrene block and any material from  
the drum.  
• Pour 2 liters of water into the main wash compartment  
of the detergent drawer in order to activate the  
ECO valve. Then run a cotton cycle at the highest tem-  
perature without any laundry in the machine, to remove  
any manufacturing residue from the drum and tub.  
Pour 1/2 a measure of detergent into the main wash  
compartment and start the machine.  
Daily use  
Load the laundry  
Measure out the detergent and the fabric softener  
Open the door by carefully  
pulling the door handle  
outwards. Place the laun-  
dry in the drum, one item  
at a time, shaking them out  
as much as possible.  
Close the door.  
6
 
Select the Delay Start by pressing button 6  
Pull out the dispenser drawer until it stops. Measure  
out the amount of detergent required, pour it into the  
Before you start the programme, if you wish to delay the  
start, press the button 6 repeatedly, to select the desired  
delay. The relevant light illuminates.  
You must select this option after you have set the pro-  
gramme and before you start the programme.  
You can cancel or modify the delay time at any moment,  
before you press button 5 .  
main wash compartment  
or in the appropriate com-  
partment if the selected programme/option it requires  
(see more details in "Detergent dispenser drawer").  
If required, pour fabric softener into the compartment  
marked  
(the amount used must not exceed the  
«MAX» mark in the drawer). Close the drawer gently.  
Selecting the delayed start:  
1. Select the programme and the required options.  
2. Select the delay start by pressing the button 6 .  
3. Press button 5 :  
Select the required programme by turning the  
programme selector dial (1)  
Turn the programme selector dial to the required pro-  
gramme. The green pilot light of the button 5 starts to  
flash.  
– the machine starts its hourly countdown.  
– The programme will start after the selected delay  
The selector dial can be turned either clockwise or coun-  
terclockwise. Turn to position « Off » to resetprogramme/  
switch the machine off.  
has expired.  
Cancelling the delayed start after having started the pro-  
gramme:  
At the end of the programme the selector dial must be  
turned to position «Off» , to switch the machine off.  
1. Set the washing machine to PAUSE by pressing but-  
ton 5 .  
2. Press button 6 once, the light relevant to the selected  
delay goes off  
3. Press button 5 again to start the programme.  
The Delay Start can not be selected with DRAIN pro-  
gramme.  
Caution! If you turn the programme selector dial to  
another programme when the machine is working,  
the red pilot light of button 5 will blink 3 times to indicate  
a wrong selection. The machine will not perform the new  
selected programme.  
Select the spin speed, the Night Cycle or the Rinse Important! The selected delay can be changed only after  
selecting the washing programme again.  
Hold option by pressing button 2  
The door will be locked throughout the delay time. If you  
needtoopenthedoor, youmustsetthemachinetoPAUSE  
(by pressing the button 5 ) and then wait a few minutes.  
After you have closed the door, press the button 5 again.  
The washing machine will automatically select the max-  
imum spin value provided for the programme you have  
chosen. (See "Washing programmes" for the maximum  
allowed spin speed).  
Press this button repeatedly to change the spin speed, if  
you want your laundry to be spun at a different speed. The  
relevant light will light up.  
Start the programme by pressing button 5  
To start the selected programme, press the button 5 , the  
corresponding green pilot light stops blinking. The pilot  
light corresponding to the running phase illuminates. The  
appliance starts operating and the door is locked.  
To interrupt a programme which is running, press the  
button 5 : the corresponding green pilot light starts blink-  
ing.  
To restart the programme from the point at which it was  
interrupted, press the button 5 again . If you have chosen  
a delayed start, the machine will begin the countdown.  
If an incorrect option is selected, the red pilot light of the  
button 5 blinks 3 times.  
Select the available options by pressing buttons 3  
and 4  
Depending on the programme, different functions can be  
combined. These must be selected after choosing the de-  
sired programme and before starting the programme.  
When these buttons are pressed, the corresponding pilot  
lights illuminate. When they are pressed again, the pilot  
lights go out. If an incorrect option is selected, the inte-  
grated red pilot light of the button 5 flashes for 3 times.  
For the compatibility among the washing pro-  
grammes and the options see chapter «Washing  
Programmes».  
7
 
If you cannot open the door but you need to open it you  
have to switch the machine off by turning the selector dial  
to Off position. After a few minutes the door can be opened  
(pay attention to the water level and temperature!) .  
After closing the door, it is necessary to select the pro-  
gramme and options again and to press button 5 .  
Altering an option or a running programme  
It is possible to change some options before the pro-  
gramme carries them out.  
Before you make any change, you must PAUSE the ap-  
pliance by pressing the button 5 .  
Changing a running programme is possible only by re-  
setting it. Turn the programme selector dialto Offand then  
to the new programme position. Start the new programme  
by pressing the button 5 again. The washing water in the  
tub will be not emptied out.  
At the end of the programme  
The machine stops automatically. The pilot light of button  
5 goes off and after a few minutes the 7.2 pilot light goes  
off. The light 7.3 illuminates. The door can be opened.  
If a programme or an option that ends with water left in  
the tub has been selected, the light 7.2 illuminates and  
the door remains locked to indicate that the water must  
be emptied out before opening the door.  
Follow the below instructions to empty out the water:  
1. Turn the programme selector dial to Off .  
2. Select the draining or spinning programme.  
3. Reduce the spin speed if needed, by pressing the  
relevant button.  
4. Press button 5 .  
At the end of the programme, the door can be now opened.  
Turn the programme selector dial to Off to switch the ma-  
chine off.  
Remove the laundry from the drum and carefully check  
that the drum is empty. If you do not intend to carry out  
another wash, close the water tap. Leave the door open to  
prevent the formation of mildew and unpleasant smells.  
Interrupting a programme  
Press the button 5 to interrupt a programme which is  
running, the corresponding green pilot light starts blink-  
ing.  
Press the button again to restart the programme.  
Cancelling a programme  
Turn the selector dial to Off position to cancel a pro-  
gramme which is running. Now you can select a new pro-  
gramme.  
Opening the door  
After the programme has started the door is locked. If, for  
any reason, you need to open it, set firstly the machine to  
PAUSE by pressing the button 5 . After a few minutes the  
pilot light 7.2 goes off and the door can be opened.  
If the door remains locked, this means that the machine  
is already heating or that the water level is too high. In  
any case, do not try to force the door!  
Helpful hints and tips  
Treat curtains with special care. Remove hooks or tie them  
up in a bag or net.  
Sorting out the laundry  
Follow the wash code symbols on each garment label and  
the manufacturer’s washing instructions. Sort the laundry  
as follows: whites, coloureds, synthetics, delicates, wool-  
lens.  
Removing stains  
Stubborn stains may not be removed by just water and  
detergent. It is therefore advisable to treat them prior to  
washing.  
Blood: treat fresh stains with cold water. For dried stains,  
soak overnight in water with a special detergent then rub  
in the soap and water.  
Oil based paint: moisten with benzine stain remover, lay  
the garment on a soft cloth and dab the stain; treat several  
times.  
Dried grease stains: moisten with turpentine, lay the gar-  
ment on a soft surface and dab the stain with the fingertips  
and a cotton cloth.  
Before loading the laundry  
Never wash whites and coloureds together. Whites may  
lose their «whiteness» in the wash.  
New coloured items may run in the first wash; they should  
therefore be washed separately the first time.  
Button up pillowcases, close zip fasteners, hooks and  
poppers. Tie any belts or long tapes.  
Remove persistent stains before washing.  
Rub particularly soiled areas with a special detergent or  
detergent paste.  
8
 
Rust: oxalic acid dissolved in hot water or a rust removing • powder detergents for delicate fabrics (60°C max) and  
product used cold. Be careful with rust stains which are  
not recent since the cellulose structure will already have  
been damaged and the fabric tends to hole.  
Mould stains: treat with bleach, rinse well (whites and fast  
coloureds only).  
woollens  
• liquid detergents, preferably for low temperature wash  
programmes (60°C max) for all types of fabric, or spe-  
cial for woollens only.  
The detergent and any additives must be placed in the  
appropriate compartments of the dispenser drawer before  
starting the wash programme.  
If using liquid detergents, a programme without prewash  
must be selected.  
Your appliance incorporates a recirculation system which  
allows an optimal use of the concentrated detergent.  
Follow the product manufacturer’s recommendations on  
quantities to use and do not exceed the «MAX» mark in  
the detergent dispenser drawer .  
Grass: soap lightly and treat with bleach (whites and fast  
coloureds only).  
1)  
Ball point pen and glue: moisten with acetone , lay the  
garment on a soft cloth and dab the stain.  
Lipstick: moisten with acetone as above, then treat stains  
with methylated spirits. Treat any residual marks with  
bleach.  
Red wine: soak in water and detergent, rinse and treat with  
acetic or citric acid, then rinse. Treat any residual marks  
with bleach.  
Quantity of detergent to be used  
Ink: depending on the type of ink, moisten the fabric first  
The type and quantity of detergent will depend on the type  
of fabric, load size, degree of soiling and hardness of the  
water used.  
Follow the product manufacturers’ instructions on quan-  
tities to use.  
Use less detergent if:  
• you are washing a small load  
1)  
with acetone , then with acetic acid; treat any residual  
marks on white fabrics with bleach and then rinse thor-  
oughly.  
Tar stains: first treat with stain remover, methylated spirits  
or benzine, then rub with detergent paste.  
Detergents and additives  
Good washing results also depend on the choice of de-  
tergent and use of the correct quantities to avoid waste  
and protect the environment.  
Although biodegradable, detergents contain substances  
which, in large quantities, can upset the delicate balance  
of nature.  
The choice of detergent will depend on the type of fabric  
(delicates, woollens, cottons, etc.), the colour, washing  
temperature and degree of soiling.  
All commonly available washing machine detergents may  
be used in this appliance:  
• the laundry is lightly soiled  
• large amounts of foam form during washing.  
Degrees of water hardness  
Water hardness is classified in so-called “degrees” of  
hardness. Information on hardness of the water in your  
area can be obtained from the relevant water supply com-  
pany, or from your local authority. If the water hardness  
degree is medium or high we suggest you to add a water  
softenerfollowing alwaysthe manufacturer’sinstructions.  
When the degree of hardness is soft, readjust the quantity  
of the detergent.  
• powder detergents for all types of fabric  
1) do not use acetone on artificial silk  
 
9
Washing Programmes  
Programme - Maximum and Minimum Temperature - Cycle  
Description - Maximum Spin Speed - Maximum Fabrics Load  
- Type of Laundry  
Options  
Detergent drawer  
3)  
COTTONS  
90° - 60°  
Main wash - Rinses  
Maximum spin speed at 1400 rpm  
Max. load 5,5 kg - Reduced load 2,5 kg  
White cotton heavily or normally soiled items.  
SPIN  
1)  
NIGHT CYCLE  
RINSE HOLD  
PREWASH  
ECONOMY  
SUPER QUICK  
EXTRA RINSE  
2)  
3)  
3)  
3)  
COTTONS  
60° - 30°  
Main wash - Rinses  
Maximum spin speed at 1400 rpm  
Max. load 5,5 kg - Reduced load 2,5 kg  
Coloured cotton normally soiled items.  
SPIN  
NIGHT CYCLE  
RINSE HOLD  
PREWASH  
ECONOMY  
SUPER QUICK  
EXTRA RINSE  
4)  
2)  
SYNTHETICS  
60° - 30°  
Main wash - Rinses  
Maximum spin speed at 900 rpm  
Max. load 3 kg - Reduced load 1,5 kg  
Synthetic or mixed fabrics: underwear, coloured garments,  
non-shrink shirts, blouses.  
SPIN  
NIGHT CYCLE  
RINSE HOLD  
PREWASH  
ECONOMY  
SUPER QUICK  
EXTRA RINSE  
4)  
2)  
DELICATES  
40° - 30°  
Main wash - Rinses  
Maximum spin speed at 700 rpm  
Max. load kg 3 - Reduced load kg 1,5  
Delicate fabrics: acrylics, viscose, polyester.  
NIGHT CYCLE  
RINSE HOLD  
PREWASH  
SUPER QUICK  
EXTRA RINSE  
2)  
WOOL  
40°- 30°  
Main wash - Rinses  
SPIN  
NIGHT CYCLE  
RINSE HOLD  
Maximum spin speed at 900 rpm  
Max. load 2 kg  
Washing programme for machine washable wool. Note : A  
single or bulky item may cause imbalance. If the appliance  
doesn’t perform the final spin phase, add more items, redis-  
tribute the load manually and then select the spinning pro-  
gramme.  
10  
 
Programme - Maximum and Minimum Temperature - Cycle  
Description - Maximum Spin Speed - Maximum Fabrics Load  
- Type of Laundry  
Options  
Detergent drawer  
HAND WASH  
40° - Cold  
Main wash - Rinses  
SPIN  
NIGHT CYCLE  
RINSE HOLD  
Maximum spin speed at 900 rpm  
Max. load 2 kg  
Special programme for delicate fabrics with «hand washing»  
care symbol.  
3)  
EASY IRON  
SPIN  
40°  
RINSE HOLD  
PREWASH  
Main wash - Rinses  
Maximum spin speed at 900 rpm  
EXTRA RINSE  
Max. load 1 kg  
Synthetic or mixed fabrics : selecting this programme the laun-  
dry is gently washed and spun to avoid any creasing. In this  
way ironing is easier. Furthermore the machine will perform  
additional rinses.  
RINSE  
Rinses  
SPIN  
NIGHT CYCLE  
RINSE HOLD  
EXTRA RINSE  
Maximum spin speed at 1400 rpm  
Max. load 5,5 kg  
With this programme it is possible to rinse and spin cotton  
garments which have been washed by hand. The machine per-  
forms 3 rinses, followed by a final long spin.  
Important!  
The spin speed will automatically assume the setting for cotton  
items. if required, reduce the spin speed.  
DRAIN  
Draining of water  
Max. load 5,5 kg  
For emptying out the water of the last rinse in programmes with  
the option Rinse Hold or Night Cycle selected.  
SPIN  
SPIN  
Drain  
Maximum spin speed at 1400 rpm  
Max. load 5,5 kg  
Separate spin for hand washed garments and after programmes  
with the Rinse Hold or Night Cycle option selected. You can  
reduce the spin speed to the required level by pressing the  
relevant button to adapt it to the fabrics to be spun.  
11  
 
Programme - Maximum and Minimum Temperature - Cycle  
Description - Maximum Spin Speed - Maximum Fabrics Load  
- Type of Laundry  
Options  
Detergent drawer  
DELICATE SPIN  
Drain  
Maximum spin speed at 700 rpm  
Max. load 3 kg  
Separate spin for hand washed garments and after programmes  
with the Rinse Hold or Night Cycle option selected. You can  
reduce the spin speed to the required level by pressing the  
relevant button to adapt it to the fabrics to be spun.  
OFF  
For cancelling the programme which is running or to switch  
the machine off .  
1) This programme at the temperature of 60° with the option ECONOMY selected, is the reference programme for the data entered in  
the energy label, in compliance with EEC 92/75 standards. It can be selected for slightly or normally soiled cotton items. The  
temperature will decrease and the washing time will be extended. This allows to obtain a good washing efficiency so saving energy.  
2) If you select the Super Quick option by pressing button 3 , we recommend that you reduce the maximum load as indicated. Full  
loading is possible however with somewhat reduced cleaning results.  
3) If using liquid detergents, a programme without PREWASH must be selected.  
4) This option is not active at a temperature lower than 40° C.  
What to do if…  
Certain problems are due to lack of simple maintenance  
Once the problem has been eliminated, press the button  
or oversights, which can be solved easily without calling 5 to restart the programme. If after all checks, the problem  
out an engineer. Before contacting your local Service  
Centre, please carry out the checks listed below.  
During machine operation it is possible that the red pilot  
light of button 5 blinks to indicate that the machine is not  
working.  
persists, contact your local Service Centre.  
12  
 
Problem  
Possible cause/Solution  
The door has not been closed (the button 5 red light blinks).  
• Close the door firmly.  
The plug is not properly inserted in the power socket.  
• Insert the plug into the power socket.  
There is no power at the socket.  
• Please check your domestic electrical installation.  
The washingmachinedoesnotstart: The main fuse has blown.  
• Replace the fuse.  
The programme selector dial is not correctly positioned and the button 5 has  
not been pressed.  
• Please turn the selector dial and press the button 5 again.  
The delay start has been selected.  
• If the laundry are to be washed immediately, cancel the delay start.  
The water tap is closed (the button 5 red light blinks).  
• Open the water tap.  
The inlet hose is squashed or kinked (the button 5 red light blinks).  
• Check the inlet hose connection.  
The filter in the inlet hose or the inlet valve filter are blocked (the button 5 red  
light blinks).  
The machine does not fill:  
• Clean the water inlet filters. (See "Cleaning the water inlet filters" for more  
details).  
The door is not properly closed (the button 5 red light blinks).  
• Close the door firmly.  
The drain hose is squashed or kinked (the button 5 red light blinks).  
• Check the drain hose connection.  
The drain filter is clogged (the button 5 red light blinks).  
• Clean the drain filter.  
An option or a programme that ends with the water still in the tub or a that  
eliminates all the spinning phases has been selected.  
The machine does not empty and/or  
does not spin:  
• Select the draining or spinning programme.  
The laundry is not evenly distributed in the drum.  
• Redistribute the laundry.  
13  
 
Problem  
Possible cause/Solution  
Too much detergent or unsuitable detergent (creates too much foam) has been  
used.  
• Reduce the detergent quantity or use another one.  
Check whether there are any leaks from one of the inlet hose fittings. It is not  
always easy to see this as the water runs down the hose; check to see if it is  
damp.  
There is water on the floor:  
• Check the water inlet hose connection.  
The drain or inlet hose is damaged.  
• Replace it with a new one.  
The emergency emptying cap has not been replaced into the filter cover or the  
filter has not been properly screwed in after cleaning action.  
• Refit the emergency emptying cap into the filter cover or screw the filter  
fully in.  
Too little detergent or unsuitable detergent has been used.  
• Increase the detergent quantity or use another one.  
Stubborn stains have not been treated prior to washing.  
• Use commercial products to treat the stubborn stains.  
The correct temperature was not selected.  
Unsatisfactory washing results:  
• Check if you have selected the correct temperature.  
Excessive laundry load.  
• Reduce the laundry load.  
The programme is still running.  
• Wait the end of washing cycle.  
The door lock has not been released.  
• Wait a few minutes before opening the door.  
There is water in the drum.  
The door will not open:  
• Select drain or spin programme to empty out the water.  
The transit bolts and packing have not been removed.  
• Check the correct installation of the appliance.  
The support feet have not been adjusted.  
• Check the correct levelling of the appliance.  
The laundry is not evenly distributed in the drum.  
The machine vibrates is noisy:  
• Redistribute the laundry.  
Maybe there is very little laundry in the drum.  
• Load more laundry.  
14  
 
Problem  
Possible cause/Solution  
The electronic unbalance detection device has cut in because the laundry is  
not evenly distributed in the drum. The laundry is redistributed by reverse  
rotation of the drum. This may happen several times before the unbalance  
disappears and normal spinning can resume. If, after 10 minutes, the laundry  
is still not evenly distributed in the drum, the machine will not spin. In this  
case, redistribute the load manually and select the spin programme.  
Spinning starts late or the machine  
does not spin:  
• Redistribute the laundry.  
The load is too small.  
• Add moreitems, redistribute the load manually and then selectthe spinning  
programme.  
If you are unable to identify or solve the problem, contact  
our service centre. Before telephoning, make a note of the  
model, serial number and purchase date of your machine:  
the Service Centre will require this information.  
Mod. ... ... ...  
Prod. No. ... ... ...  
Ser. No. ... ... ...  
Technical data  
Dimensions  
Width  
Height  
Depth  
60 cm  
85 cm  
60 cm  
63 cm  
Depth (Overall dimensions)  
Electrical connection  
Voltage - Overall power - Fuse  
Information on the electrical connection is given on the rating plate, on the  
inner edge of the appliance door.  
Water supply pressure  
Minimum  
Maximum  
0,05 MPa  
0,8 MPa  
Maximum Load  
Spin Speed  
Cotton  
5,5 kg  
Maximum  
1400 rpm  
Consumption values  
Programme  
Energy consumption  
(KWh)  
Water consumption (litres) Programme duration (Mi-  
nutes)  
White Cottons 90°  
Cottons 60°  
1.9  
1.2  
58  
54  
49  
130  
120  
140  
Cottons + ECONOMY 60°  
1)  
0.93  
15  
 
Programme  
Cottons 40°  
Energy consumption  
(KWh)  
Water consumption (litres) Programme duration (Mi-  
nutes)  
0.6  
0.5  
54  
50  
50  
53  
115  
80  
Synthetics 40°  
Delicates 40°  
Wool 30°  
0.55  
0.25  
65  
55  
1) «Cottons + Economy» at 60°C with a load of 5,5 kg is the reference programme for the data entered in the energy label, in  
compliance with EEC 92/75 standards.  
The consumption data shown on this chart is to be considered purely indicative, as it may vary depending on  
the quantity and type of laundry, on the inlet water temperature and on the ambient temperature.  
Care and cleaning  
Warning! You must DISCONNECT the appliance  
from the electricity supply, before you can carry out  
any cleaning or maintenance work.  
Descaling  
The water we use normally contains lime. It is a good idea  
to periodically use a water softening powder in the ma-  
chine. Do this separately from any laundry washing, and  
according to the softening powder manufacturer's in-  
structions. This will help to prevent the formation of lime  
deposits.  
Remove the drawer by  
pressing the catch down- part of the additive com-  
wards and by pulling it partment should be re-  
out. Flush it out under a moved.  
tap, to remove any traces  
To aid cleaning, the top  
External cleaning  
Clean the exterior cabinet of the appliance with soap and  
water only, and then dry thoroughly.  
of accumulated powder.  
Cleaning the dispenser drawer  
The washing powder and additive dispenser drawer  
should be cleaned regularly.  
Cleaning the drawer recess  
Having removed the draw-  
er, use a small brush to  
clean the recess, ensuring  
that all washing powder  
residue is removed from  
the upper and lower part of  
the recess.  
Replace the drawer and run the rinse programme with-  
out any clothes in the drum.  
Cleaning the pump  
The pump should be inspected if:  
• the machine does not empty and/or spin;  
16  
 
• the machine makes an unusual noise during draining  
due to objects such as safety pins, coins etc. blocking  
the pump.  
Proceed as follows:  
• disconnect the appliance;  
Never removethepumpcoverduringawashcycle, always  
wait until the appliance has finished the cycle, and is  
empty. When replacing the cover, ensure it is securely re-  
tightened so as to stop leaks and young children being  
able to remove it.  
• if necessary wait until the water has cooled down.  
Cleaning the water inlet filters  
Important! If the appliance doesn't fill, takes long to fill  
water, the starting button blinks yellow or the display (if  
available) shows the relevant alarm (see chapter "What to  
do if..." for more details), check if the water inlet filters are  
blocked .  
Open the pump door.  
Place a container close to  
the pump to collect any  
spillage.  
To clean the water inlet filters:  
• Turn off the water tap.  
• Unscrew the hose from  
the tap.  
• Clean the filter in the  
hose with a stiff brush.  
Pull out the emergency  
emptying hose, place it in  
the container and remove  
its cap.  
• Screw the hose back onto the tap. Make sure the  
connection is tight.  
When no more water comes out, unscrew the pump  
cover and remove it. Always keep a rag nearby to dry  
up spillage of water when removing the cover.  
Remove any objects from  
the pump impeller by ro-  
tating it.  
Put the cap back on the  
emergency emptying hose  
and place the latter back in  
its seat.  
• Unscrew the hose from the machine. Keep a rug  
nearby because some water may flow.  
• Clean the filter in the valve with a stiff brush or with  
the piece of cloth.  
Screw the pump cover  
fully in.  
Close the pump door.  
35°  
45°  
Caution! When the appliance is in use and  
depending on the programme selected there can be  
hot water in the pump.  
17  
 
• pull out the plug from the power socket;  
• close the water tap;  
• if necessary, wait until the water has cooled down;  
• open the pump door;  
• Screw the hose back to the machine and make sure  
the connection is tight.  
• Turn on the water tap.  
• place a bowl on the floor and place the end of the  
emergency emptying hose into the bowl. Remove its  
cap. The water should drain by gravity into the bowl.  
When the bowl is full, put the cap back on the hose.  
Empty the bowl. Repeat the procedure until water stops  
flowing out;  
• clean the pump if necessary as previously described;  
• replace the emergency emptying hose in its seat after  
having plugged it;  
Frost precaution  
If the machine is exposed to temperatures below 0°C,  
certain precautions should be taken.  
• Turn off the water tap.  
• Unscrew the inlet hose.  
• Place the end of the emergency emptying hose and that  
of the inlet hose in a bowl placed on the floor and let  
water drain out.  
• Screw the water inlet hose back on and reposition the  
emergency emptying hose after having put the cap on  
again.  
• When you intend to start the machine up again, make  
sure that the room temperature is above 0°C.  
• screw the pump cover again and close the door.  
Important! Every time you drain the water through the  
emergency emptying hose you must pour 2 litres of water  
into the main wash compartment of the detergent drawer  
and then run the drain programme. This will activate the  
ECO Valve device avoiding that part of the detergent  
remains unused at next washing.  
Emergency emptying out  
If the water is not discharged, proceed as follows to empty  
out the machine:  
Installation  
Unpacking  
All transit bolts and packing must be removed before us-  
ing the appliance.  
You are advised to keep all transit devices so that they  
can be refitted if the machine ever has to be transported  
again.  
Unscrew the three bolts. Slide outtherelevantplas-  
tic spacers.  
After removing all the  
packaging, carefully lay  
Remove the power supply  
cable and the hoses from  
machine on it's back to re- the hose holders on the  
move thepolystyrenebase rear of the appliance.  
from the bottom.  
18  
 
The inlet hose is screwed to the back of the appliance.  
Connect the hose to a tap  
with a 3/4” thread. Always  
use the hose supplied with  
the appliance.  
Open the porthole and re- Fill the smaller upper hole  
move the polystyrene  
block fitted on the door  
seal.  
and the two large ones  
with the corresponding  
plastic plug caps supplied  
in the bag containing the  
instruction booklet.  
35°  
45°  
Positioning  
Install the machine on a flat hard floor. Make sure that air  
circulation around the machine is not impeded bycarpets,  
rugs etc. Check that the machine does not touch the wall  
or other kitchen units. Level the washing machine by  
raising or lowering the feet. The feet may be tight to adjust  
as they incorporate a self locking nut, but the machine  
MUST be level and stable.  
Any necessary adjustment can be made with a spanner.  
Accurate levelling prevents vibration, noise and displace-  
ment of the machine during operation. Never place card-  
board, wood or similar materials under the machine to  
compensate for any unevenness in the floor.  
The other end of the inlet hose which connects to the  
appliance can be turned as showed in the picture.  
Do not place the inlet hose downwards. Angle the hose  
to the left or right depending on the position of your  
water tap. Set the hose correctly by loosening the ring  
nut. After positioning the inlet hose, be sure to tighten  
the ring nut again to prevent leaks.  
Caution! The inlet hose must not be lengthened. If  
it is too short and you do not wish to move the tap,  
you will have to purchase a new, longer hose specially  
designed for this type of use.  
If necessary, check the  
setting with a spirit level.  
Warning! Installation should comply with local  
water authority and building regulations’  
requirements.  
The appliance must be connected to a cold water supply.  
A minimum water pressure of 0.05 MPa (0.5 bar) is  
required for safe operation of the appliance.  
If you cannot make the cold water connection direct from  
the rising mains, you may be able to operate the appliance  
from your cold water storage system.  
Water inlet  
There should be a minimum vertical distance of 5.02 m  
(16.5 ft) between the appliance’s inlet and the bottom of  
the water storage tank.  
Warning! This appliance must be connected to a  
cold water supply  
Caution! Before connecting up the appliance to new  
pipework or to pipework that has not been used for  
some time, run off a reasonable amount of water to flush  
out any debris that may have collected  
Water drainage  
This appliance is designed to be permanently plumbed  
into your home's drainage system using one of the fol-  
lowing methods.  
Caution! Do not use the hose from your previous  
appliance to connect to water supply.  
1. Into a drainage standpipe.  
19  
 
2. Onto a sink outlet spigot.  
Firstly form a hook in the end of the drain hose using  
the “U” piece” supplied.  
Loop  
“U” piece supplied  
If the outlet spigot has not Push the drain hose onto  
been used before, remove the spigot and secure with  
Place the drain hose into your standpipe, which should  
have an internal diameter of approximately 38 mm thus  
ensuring there is an air break between the drain hose  
and standpipe.  
When discharging into a standpipe ensure that the top  
of the standpipe is no more than 90 cm (35.4'') and no  
less than 60 cm (23.6'') above floor level.  
any blanking plug that  
may be in place.  
a clip, ensure a loop is  
formed in the drain hose  
(see above) to prevent  
waste from the sink enter-  
ing the appliance.  
If you intend to drain the hose from the machine into a  
sink, make sure that the sink is empty and the plug hole  
is not blocked. Use the plastic “U - Piece” supplied.  
38 mm (1.5”)  
standpipe  
diamater  
30 cm (12”)  
Special conditions  
If the floor is carpeted or covered with crumbly or soft  
material, insert a rigid support base under the feet to pre-  
vent noise, vibration or displacement. The base should  
protrude a few centimetres beyond the edges of the ap-  
pliance.  
The drain hose may be extended to a maximum of 4  
metres. An additional drain hose and joining piece is  
available from your local Service Force Centre. The  
joining piece must have an internal diameter of 18 mm.  
Warning! The appliance should NOT be placed on  
deep pile carpeting.  
Note!  
Please ensure that when the appliance is installed it is  
easily accessible for the engineer in the event of a  
breakdown.  
In the interest of the environment  
The appliance should be connected to the FOUL drainage  
system, the water will then be taken to a sewage works for  
treatment before being discharged safely into a river.  
It is essential that these appliances are not connected to  
the surface water drainage system as this water is dis-  
charged directly into a river or stream and may cause  
pollution.  
Min. 60 cm (23.6”)  
Max. 90 cm (35.4”)  
If your drain hose looks  
like this (see beside) you  
do not require the “U”  
piece”. Just push the hose  
firmly in to the standpipe.  
If you require any further advice please contact your local  
water authority.  
20  
 
1
2
3
4
Green & Yellow  
Brown  
Cord clamp  
Blue  
1
SHOWER  
TOILET  
SINK  
BATH  
BIDET  
2
WASHING  
MACHINE  
3
4
DISHWASHER  
RAINWATER  
‘RUN-OFF’  
The wire coloured green and yellow must be connected  
to the terminal marked with the letter «E» or by the earth  
FOUL DRAIN  
SURFACE WATER  
DRAINS & SEWERS  
FOUL SEWERS  
symbol  
or coloured green and yellow.  
The wire coloured blue must be connected to the terminal  
«N» or coloured black.  
The wire coloured brown must be connected to the ter-  
minal marked «L» or coloured red.  
SEWAGE TREATMENT  
WORKS  
TREATED DISCHARGE  
RIVER  
UNTREATED  
DISCHARGE  
RIVER  
Upon completion there must be no cut, or stray strands  
of wire present and the cord clamp must be secure over  
the outer sheath.  
Electrical connection  
Any electrical work required to install this appliance  
should be carried out by a qualified electrician or com-  
petent person.  
Warning! A cut off plug inserted into a 13 amp  
socket is a serious safety (shock) hazard.  
Warning! THIS APPLIANCE MUST BE EARTHED.  
Ensure that the cut off plug is disposed of safely. Should  
The manufacturer declines any liability should this the appliance power supply cable need to be replaced,  
safety measure not be observed.  
this must be carried out by our Service Force Centre. The  
appliance should not be connected to the electricalsupply  
by means of an extension cable.  
Before switching on, make sure the electricity supply  
voltage is the same as that indicated on the appliance’s  
rating plate.  
Note!  
Warning! Information on the electrical connection  
is given on the rating plate on the inner edge of the  
appliance door.  
When the appliance is installed the power supply cable  
must be accessible.  
Permanent connection  
In the case of permanent connection it is necessary that  
you install a double pole switch between the appliance  
and the electricity supply (mains), with a minimum gap  
of 3 mm between the switch contacts and of a typesuitable  
for the required load in compliance with the current elec-  
trical regulations.  
The appliance is supplied with a 13 amp plug fitted.  
In the event of having to change the fuse in the plug sup-  
plied, a 13 amp ASTA approved (BS1363/A) fuse must be  
used.  
Should the plug need to be replaced for any reason, pro-  
ceed as described below.  
The switch must not break the yellow and green earth  
cable at any point.  
The wires in the mains lead are coloured in accordance  
with the following code:  
Environment concerns  
disposed of correctly, you will help prevent potential  
negative consequences for the environment and human  
health, which could otherwise be caused by inappropriate  
waste handling of this product. For more detailed  
information about recycling of this product, please  
The symbol  
on the product or on its packaging  
indicates that this product may not be treated as  
household waste. Instead it should be taken to the  
appropriate collection point for the recycling of electrical  
and electronic equipment. By ensuring this product is  
21  
 
• Normally soiled laundry may be washed without pre-  
washing in order to save detergent, water and time (the  
environment is protected too!).  
• The machine works more economically if it is fully  
loaded.  
• Withadequatepre-treatment, stainsandlimitedsoiling  
can be removed; the laundry can then be washed at a  
lower temperature.  
contactyourlocalcouncil, yourhouseholdwastedisposal  
service or the shop where you purchased the product.  
Packaging materials  
The materials marked with the symbol are recyclable.  
>PE<=polyethylene  
>PS<=polystyrene  
>PP<=polypropylene  
This meansthatthey can be recycled by disposingofthem  
properly in appropriate collection containers.  
• Measure out detergent according to the water hard-  
ness, the degree of soiling and the quantity of laundry  
being washed.  
Ecological hints  
To save water, energyandto helpprotecttheenvironment,  
we recommend that you follow these tips:  
22  
 
23  
 

Weider Home Gym 831150312 User Manual
Westinghouse Landscape Lighting W 164 User Manual
Whirlpool Oven GW395LEPB03 User Manual
Wibur Curtis Company Coffee Grinder DHG User Manual
Wolf Griddle RCSIZEE User Manual
X10 Wireless Technology DVR IR10A User Manual
Xpelair Fan CX10 User Manual
Yamaha Musical Instrument CVP 49 User Manual
Zanussi Oven ZDA 45 User Manual
Zebra Technologies Printer Mobile Printer User Manual