Woodstock Styling Iron D3119 User Manual

Figure 1.  
Workpiece  
Guide  
Board  
BOARD STRAIGHTENERS  
INSTRUCTION SHEET  
D3119 Board Straighteners™  
Introduction  
You can now cut straight boards from irregular-edged  
boards without using a jointer! The SHOP FOX®  
Model D3119 Board Straightenershold a board with  
an irregular edge to a guide board with a known  
straight edge. This stable arrangement can then be slid  
along the table saw fence, producing a straight cut on  
the irregular board.  
Guide board  
is against  
fence  
Workpiece  
• READ and UNDERSTAND this instruction  
sheet and your table saw instruction manual  
before you use Board Straighteners. Otherwise,  
serious personal injury may occur.  
Figure 2.  
• If you are using BOARD BUDDIES® or any other  
anti-kickback device on your table saw, make sure  
that no interference or unsafe condition exists if  
used in conjunction with Board Straighteners.  
How to Use Your Board Straighteners™  
To hold and cut an irregular-edged board without the use  
of a jointer, do these steps and see Figures 1 and 2.  
1. Choose a straight and square  
piece of 12" thick wood for the  
guide board, which is the same  
• Always use two or more Board Straightenersto  
hold the workpiece to the guide board; otherwise,  
the boards can slip apart, causing kickback. It is  
often better to use too-many Board Straighteners™  
than too-few.  
112  
"
length or longer than the  
workpiece you will cut; and  
316"  
3
make a 16" deep by 112" wide  
rabbet cut the complete length  
of your needed guide board.  
• ONLY use Board Straightenersfor holding an  
irregular-edged board to a guide board for cutting  
on your table saw. Board Straightenersare not  
designed for cutting warped boards, which do not  
sit flat on the table. DO NOT modify Board  
Straightenersfor any other task, but rather, use  
“C” clamps, vises, jigs, and bar clamps for  
associated clamping and gluing needs.  
2. Position the guide board and workpiece to either side of  
the Board Straightenersas shown in Figure 1.  
3. Tighten the thumbscrews until the boards are securely held.  
For long boards–use additional Board StraightenersDO  
NOT over tighten the thumbscrews.  
4. Slide the guide board against the fence and make your  
first cut, remove the workpiece from the Board  
Straighteners, and put the freshly-cut side of the  
workpiece against the fence and make your second cut.  
The workpiece is now square.  
• Woodstock International Inc. shall not be  
responsible for damage or injuries caused by  
improper use of the Board Straighteners. If you  
have any questions about the use of this tool,  
contact Woodstock International Inc.  
For questions contact Woodstock International Technical Support at 360-734-3482, or send e-mail to: [email protected].  
COPYRIGHT© APRIL 2003 BY WOODSTOCK INTERNATIONAL, INC. WARNING: NO PORTION OF THIS DOCUMENT MAY BE  
REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.  
 

Weed Eater Trimmer 530088895 User Manual
Whirlpool Washer 7MWT9601WW0 User Manual
White Rodgers Air Conditioner 1F85 277 User Manual
White Westinghouse Clothes Dryer WEQ332HS0 User Manual
Wibur Curtis Company Coffeemaker C500AP User Manual
Woodstock Drill D4033 User Manual
Wright Manufacturing Lawn Mower Sentar S User Manual
X10 Wireless Technology Home Security System XX20A User Manual
Xantrex Technology Universal Remote RC7 User Manual
Yamaha Guitar APX 5 12A User Manual